Full Text
APPROVALS T&D MGR CITY OF ANAHEIM ELECTRICAL DIVISION PUBLIC UTILITIES DEPARTMENT FILENAME: REVISION KEYS: ADDED / REVISED TEXT NEW SHEET CONSTRUCTION STANDARD: ADDED / REVISED MATERIAL SHEET OF REVISION NO. ISSUE DATE : FIELD MGR OPER. MGR T&D CONSTRUCTION STANDARDS PROTECTIVE POSTS CU1600-9 REV2 2 01-10 1 2 CU 1600-9 ARMORCAST POST SLEEVE (SEE NOTE 5) FINAL GRADE PEA GRAVEL 18"DIA. MIN. CONCRETE FOOTING 5 SACK MIX SELF DRILLING SCREW (2X) 4" IPS GALVANIZED PIPE-HOLLOW 5" IPS GALVANIZED PIPE SLEEVE 1/4" DIA. ANTISUCTION HOLES (4X) (SEE NOTE 3 & 4) TYPICAL EQUIPMENT PAD AND POST LAYOUT SEE NOTE 4 NON-REMOVABLE POST DETAIL SELF DRILLING SCREW (2X) FINAL GRADE ARMORCAST POST SLEEVE (SEE NOTE 5) 4" IPS GALVANIZED PIPE-CONCRETE FILLED VAULT VENT POLE OR 3" REMOVABLE POST DETAIL 36" OR 48" (NOTE 5) 36" 36" MIN. 60" MAX. 18" 18" 36" MIN. 60" MAX. (TYP.) 18" 36" MIN. 36" MIN. 36" MIN. 60" MAX. 6" 36" SCOPE: THIS STANDARD SHOWS PROTECTIVE POST REQUIREMENTS FOR ABOVE GRADE MOUNTED EQUIPMENT EXPOSED TO VEHICULAR TRAFFIC. FORM CONCRETE CAP IF POST WILL BE PAINTED FORM CONCRETE CAP OVER PACKING IF POST WILL BE PAINTED PACKING EQUIPMENT PAD 18"DIA. MIN. CONCRETE FOOTING 5 SACK MIX 36" OR 48" (NOTE 5) 6" REFLECTIVE SILVER TAPE (TYP) 36" OR 48" 2" POST-GREEN 2" 2" 2" 2" TYPICAL POLE OR VENT AND POST LAYOUT EQUIPMENT DOOR ---PAGE BREAK--- APPROVALS T&D MGR CITY OF ANAHEIM ELECTRICAL DIVISION PUBLIC UTILITIES DEPARTMENT FILENAME: REVISION KEYS: ADDED / REVISED TEXT NEW SHEET CONSTRUCTION STANDARD: ADDED / REVISED MATERIAL SHEET OF REVISION NO. ISSUE DATE : FIELD MGR OPER. MGR T&D CONSTRUCTION STANDARDS PROTECTIVE POSTS CU1600-9 REV2 2 01-10 2 2 CU 1600-9 P6000560S P6000560 SLEEVE, POLYETHYLENE - YELLOW PART NO. ARMORCAST DESCRIPTION ITEM ARMORCAST PRODUCTS SLEEVE ONLY SLEEVE, POLYETHYLENE - YELLOW POST, 4" IPS X 72" LG PIPE, GALVANIZED NON-REMOVABLE POST KIT SLEEVE, POLYETHYLENE - YELLOW POST, 4" IPS X 72" LG PIPE, GALVANIZED SLEEVE, 5" IPS X 36" LG PIPE, GALVANIZED REMOVABLE POST KIT P6000560A NOTES: 1. PROTECTIVE POSTS INSTALLATION GUIDELINES: A. DO NOT INSTALL PROTECTIVE POSTS IF EXISTING ABOVE GROUND OBJECTS CAN PROTECT THE EQUIPMENT FROM VEHICULAR TRAFFIC A. GREEN COLOR POSTS ( PAINTED /SLEEVED ) MAY BE UTILIZED WHEN, AND IF THE ABOVE GROUND MOUNTED EQUIPMENT, ARE INSTALLED IN LANDSCAPED AREA WITH LIMITED TRAFFIC ACCESS. POSTS SHALL BE PAINTED YELLOW FOR DESIGNATING CAUTION AND FOR MARKING PHYSICAL HAZARDS, PER OSHA RREGULATION 1910. 144. REFLECTIVE TAPES ARE REQUIRED PER DETAIL ONLY ON GREEN POSTS. FINAL DETERMINATION OF QUANTITY, COLOR AND HEIGHT OF THE POSTS SHALL BE MADE BY THE ELECTRICAL DESIGNER AND/OR THE ELECTRIC UTILTIY INSPECTOR 2. CAUTION MUST BE TAKEN WHEN INSTALLING POSTS SO THEY DO NOT MAKE CONTACT WITH ANY UNDER GROUND UTILITIES. 3. 18" SIDE DIM. SHALL BE INCREASED TO 48" FOR PAD MOUNTED SWITCHES. 4. POSTS SHALL BE COVERED WITH APPROPRIATE COLORED PLASTIC SLEEVE AND SECURED WITH SELF DRILLING SCREWS (SEE PART NUMBERS BELOW) OR PAINTED AT THE JOB SITE. 5. EQUIPMENT HEIGHT DICTATES THE HEIGHT OF PROTECTIVE POSTS. USE TALLER POSTS FOR SHORTER EQUIPMENT. SLEEVE, POLYETHYLENE - GREEN SLEEVE ONLY SLEEVE, POLYETHYLENE - GREEN POST, 4" IPS X 72" LG PIPE, GALVANIZED NON-REMOVABLE POST KIT SLEEVE, POLYETHYLENE - GREEN POST, 4" IPS X 72" LG PIPE, GALVANIZED SLEEVE, 5" IPS X 36" LG PIPE, GALVANIZED REMOVABLE POST KIT P6000560-GRN P6000560S-GRN P6000560A-GRN - 3M PRODUCT #963-10 2" REFLECTIVE TAPE ANAHEIM PART NO. E566095M